Firmware¶
DDCS Parameters¶
List of available parameters in the controller. See manual for full descriptions.
Important
This list does not represent the current settings of any particular machine, they are factory defaults.
#1 -t2 -s1 "language setting" -s3 "0:eng,1:chs" -m16 -min=0.000 -max=1.000 -i0 "Eng" -i1 "ÖÐÎÄ"
#2 -t1 -s1 "Display response during working" -m16 -min=400 -max=10000
#3 -t2 -s1 "Function of tool path key" -m0 -min=0.000 -max=1.000 -i0 "tool path" -i1 "Try cutting "
#5 -t1 -s1 "minimum log radius of 4axis machining" -s2 "mm" -m1 -min=3.000 -max=999.999
#6 -t2 -s1 "A axis rotate reference axis" -m1 -min=0.000 -max=3.000 -i0 "X axis" -i1 "Y axis" -i2 "Z axis"-i3 "not rotate"
#8 =1.000
#9 =1.000
#12 =1.000
#13 =1.000
#14 =1.000
#15 -t2 -s1 "Speed Selection" -s3 "0:set by G code,1:use default speed" -m4 -min=0.000 -max=1.000 -i0 "G code"-i1 "default"
#16 -t2 -s1 "current coordinate system" -s3 "0:G53,1:G54,2:G55,3:G56,4:G57,5:G58,6:G59,7:MACH"-m5 -min=1.000 -max=7.000 -i0 "G53"-i1 "G54" -i2 "G55" -i3 "G56" -i4 "G57" -i5 "G58" -i6 "G59" -i7 "MACH "
#18 -t1=200.0
#19 -t1=200.0
#20 -t1=3.0
#33 -t1 -s1 "Motor start speed" -s2 "mm/min" -m2 -min=0.000 -max=999.000
#34 -t1 -s1 "X axis pulse equivalency" -s2 "pulse/mm" -m2 -min=50.000 -max=99999.000
#35 -t1 -s1 "Y axis pulse equivalency" -s2 "pulse/mm" -m2 -min=50.000 -max=99999.000
#36 -t1 -s1 "Z axis pulse equivalency" -s2 "pulse/mm" -m2 -min=50.000 -max=99999.000
#37 -m0
#38 -t1 -s1 "A axis pulse equivalency" -s2 "" -m2 -min=50.000 -max=999999.000
#39 -t2 -s1 "A axis pulse unit" -m2 -min=0.000 -max=1.000 -i0 "pulse/deg" -i1 "pulse/circle "
#40 -t2 -s1 "AB axis Selection" -m2 -min=0.000 -max=1.000 -i0 "A axis" -i1 "B axis "
#41 -t1 -s1 "X Axis max speed in M_Ctrl mode" -s2 "mm/min" -m3 -min=99.000 -max=99999.000
#42 -t1 -s1 "Y Axis max speed in M_Ctrl mode" -s2 "mm/min" -m3 -min=99.000 -max=99999.000
#43 -t1 -s1 "Z Axis max speed in M_Ctrl mode" -s2 "mm/min" -m3 -min=99.000 -max=99999.000
#44 -t1 -s1 "A Axis max speed in M_Ctrl mode" -s2 "deg/min" -m3 -min=99.000 -max=99999.000
#45 -t1 -s1 "X axis start Acc in M_Ctrl mode" -s2 "mm/s2" -m3 -min=9.000 -max=9999.000
#46 -t1 -s1 "Y axis start Acc in M_Ctrl mode" -s2 "mm/s2" -m3 -min=9.000 -max=9999.000
#47 -t1 -s1 "Z axis start Acc in M_Ctrl mode" -s2 "mm/s2" -m3 -min=9.000 -max=9999.000
#48 -t1 -s1 "A axis start Acc in M_Ctrl mode" -s2 "deg/s2" -m3 -min=9.000 -max=9999.000
#49 -t0 -s1 "HOME times" -m8 -min=1.000 -max=5.000
#50 -t2 -s1 "HOME signal Effective when HOME" -m8 -min=0.000 -max=1.000 -i0 "Ignore HOME" -i1 "Continue HOME "
#51 -t2 -s1 "Enable limit signal when HOME" -s3 "0:Disable,1:Enable" -m8 -min=0.000 -max=1.000 -i0 "Disable" -i1 "Enable "
#52 -t2 -s1 "Enable X Home Searching function" -s3 "0:not enable,1:enable" -m8 -min=0.000 -max=1.000 -i0 "Disable" -i1 "Enable "
#53 -t2 -s1 "Enable Y Home Searching function" -s3 "0:not enable,1:enable" -m8 -min=0.000 -max=1.000 -i0 "Disable" -i1 "Enable "
#54 -t2 -s1 "Enable Z Home Searching function" -s3 "0:not enable,1:enable" -m8 -min=0.000 -max=1.000 -i0 "Disable" -i1 "Enable "
#55 -t2 -s1 "Enable Z Home Searching function" -s3 "0:not enable,1:enable" -m8 -min=0.000 -max=1.000 -i0 "Disable" -i1 "Enable "
#56 -t1 -s1 "X axis Home speed" -s2 "mm/min" -m8 -min=99.000 -max=99999.000
#57 -t1 -s1 "Y axis Home speed" -s2 "mm/min" -m8 -min=99.000 -max=99999.000
#58 -t1 -s1 "Z axis Home speed" -s2 "mm/min" -m8 -min=99.000 -max=99999.000
#59 -t1 -s1 "A axis Home speed" -s2 "deg/min" -m8 -min=99.000 -max=99999.000
#60 -t2 -s1 "X axis Home signal Electric Level" -m8 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#61 -t2 -s1 "Y axis Home signal Electric Level" -m8 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#62 -t2 -s1 "Z axis Home signal Electric Level" -m8 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#63 -t2 -s1 "A axis Home signal Electric Level" -m8 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#64 -t2 -s1 "X axis Home direction" -m8 -min=0.000 -max=1.000 -i0 "Negative" -i1 "Positive "
#65 -t2 -s1 "Y axis Home direction" -m8 -min=0.000 -max=1.000 -i0 "Negative" -i1 "Positive "
#66 -t2 -s1 "Z axis Home direction" -m8 -min=0.000 -max=1.000 -i0 "Negative" -i1 "Positive "
#67 -t2 -s1 "A axis Home direction" -m8 -min=0.000 -max=1.000 -i0 "Negative" -i1 "Positive "
#68 -t2 -s1 "Tool Setting function mode " -m9 -min=0.000 -max=2.000 -i0 "Disable" -i1 "mode 1" -i2 "mode 2 "
#69 -t1 -s1 "Thickness of tool sensor" -s2 "mm" -m9 -min=-99.000 -max=99.000
#70 -t2 -s1 "Probe signal electric level" -m9 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#71 -t2 -s1 "Initial tool's position" -m9 -min=0.000 -max=1.000 -i0 "current position" -i1 "fixed position "
#72 -t1 -s1 "Initial probe position on X axis" -s2 "mm" -m9 -min=-9999.000 -max=9999.000
#73 -t1 -s1 "Initial probe position on Y axis" -s2 "mm" -m9 -min=-9999.000 -max=9999.000
#74 -t1 -s1 "Initial probe position on Z axis" -s2 "mm" -m9 -min=-9999.000 -max=9999.000
#75 -t1 -s1 "back distance after probe" -s2 "mm" -m9 -min=0.000 -max=99.000
#76 -t1 -s1 "default operation speed" -s2 "mm/min" -m4 -min=10.000 -max=99999.000
#77 -t1 -s1 "maximum speed" -s2 "mm/min" -m4 -min=99.000 -max=99999.000
#78 -t1 -s1 "Z axis lifting protection speed" -s2 "mm/min" -m4 -min=99.000 -max=99999.000
#79 -t1 -s1 "Z axis dropping protection speed" -m4 -min=99.000 -max=99999.000
#80 -t1 -s1 "G0 Speed" -s2 "mm/min" -m4 -min=99.000 -max=99999.000
#82 -t1 -s1 "Z axis safe height" -s2 "mm" -m4 -min=0.000 -max=99.000
#83 -t1 -s1 "X axis back distance after Home" -s2 "mm" -m8 -min=0.000 -max=99.000
#84 -t1 -s1 "Y axis back distance after Home" -s2 "mm" -m8 -min=0.000 -max=99.000
#85 -t1 -s1 "Z axis back distance after Home" -s2 "mm" -m8 -min=0.000 -max=99.000
#86 -t1 -s1 "A axis back distance after Home" -s2 "deg" -m8 -min=0.000 -max=360.000
#88 -t2 -s1 "enable of beep " -m16 -min=0.000 -max=1.000 -i0 "Disable" -i1 "Enable "
#89 -t1 -s1 "Z axis back distance when pause" -s2 "mm" -m4 -min=0.000 -max=99.000
#98 -t1 -s1 "maximum spindle speed" -s2 "rpm" -m6 -min=99.000 -max=99999.000
#99 -t1 -s1 "operation acceleration" -s2 "mm/s2" -m4 -min=9.000 -max=9999.000
#100 -t1 -s1 "X axis manual control speed" -s2 "mm/min" -m3 -min=99.000 -max=99999.000
#101 -t1 -s1 "Y axis manual control speed" -s2 "mm/min" -m3 -min=99.000 -max=99999.000
#102 -t1 -s1 "Z axis manual control speed" -s2 "mm/min" -m3 -min=99.000 -max=99999.000
#103 -t1 -s1 "A axis manual control speed" -s2 "deg/min" -m3 -min=99.000 -max=99999.000
#104 -t2 -s1 "A axis optimal path when G0 run" -m1 -min=0.000 -max=1.000 -i0 "No" -i1 "Yes "
#108 -t2 -s1 "M Bus IO command response" -s3 "0:not response,1:response" -m7 -min=0.000 -max=1.000 -i0 "No" -i1 "Yes "
#109 -t0 -s1 "M Bus IO default status" -m7 -min=0 -max=4294967295
#192 -t1=100.0
#193 -t1=100.0
#194 -t1=3.0
#195 =0
#196 =0
#218 -t2 -s1 "Cycle Start key mode selection" -m16 -min=0.000 -max=1.000 -i0 "Pause start" -i1 "Restart "
#219 -t2 -s1 "If Stop Spindle when pause" -m6 -min=0.000 -max=1.000 -i0 "No" -i1 "Yes "
#220 -t2 -s1 "Spindle speed selection" -s3 "0:set by G code,1:default speed of spindle" -m6 -min=0.000 -max=1.000 -i0 "G code" -i1 "default "
#221 -t1 -s1 "default spindle speed" -s2 "rpm" -m6 -min=10.000 -max=99999.000
#222 -t2 -s1 "Spindle commands M3/M5 response" -s3 "0:not response,1:response" -m6 -min=0.000 -max=1.000 -i0 "No" -i1 "Yes "
#223 -t2 -s1 "response of M code(M8/M9,M10/M11)" -s3 "0:not response,1:response" -m7 -min=0.000 -max=1.000 -i0 "No" -i1 "Yes "
#224 -t1 -s1 "Spindle M3/M4/M5 response Duration" -s2 "s" -m6 -min=0.000 -max=9.000
#225 -t1 -s1 "delay time of M8/M9" -s2 "s" -m7 -min=0.000 -max=9.000
#226 -t1 -s1 "delay time of M10/M11" -s2 "s" -m7 -min=0.000 -max=9.000
#227 -t2 -s1 "Spindle switch Active level" -m6 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#228 -t2 -s1 "M8/M9 active electric level" -m7 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#229 -t2 -s1 "M10/M11 active electric level" -m7 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#250 -t2 -s1 "real track paint enable" -m16 -min=0.000 -max=1.000 -i0 "disable" -i1 "enable "
#253 -t2 -s1 "track paint mode" -m16 -min=0.000 -max=1.000 -i0 "Statue Mode" -i1 "Line Mode "
#263 -t1 -s1 "X axis stop Acc in M_Ctrl mode" -s2 "mm/s2" -m3 -min=9.000 -max=9999.000
#264 -t1 -s1 "Y axis stop Acc in M_Ctrl mode" -s2 "mm/s2" -m3 -min=9.000 -max=9999.000
#265 -t1 -s1 "Z axis stop Acc in M_Ctrl mode" -s2 "mm/s2" -m3 -min=9.000 -max=9999.000
#266 -t1 -s1 "A axis stop Acc in M_Ctrl mode" -s2 "deg/s2" -m3 -min=9.000 -max=9999.000
#267 -t1 -s1 "H00 tool offset" -s2 "mm" -m0 -min=-999.999 -max=999.999
#268 -t1 -s1 "H01 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#269 -t1 -s1 "H02 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#270 -t1 -s1 "H03 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#271 -t1 -s1 "H04 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#272 -t1 -s1 "H05 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#273 -t1 -s1 "H06 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#274 -t1 -s1 "H07 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#275 -t1 -s1 "H08 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#276 -t1 -s1 "H09 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#277 -t1 -s1 "H10 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#278 -t1 -s1 "H11 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#279 -t1 -s1 "H12 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#280 -t1 -s1 "H13 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#281 -t1 -s1 "H14 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#282 -t1 -s1 "H15 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#283 -t1 -s1 "D00 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#284 -t1 -s1 "D01 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#285 -t1 -s1 "D02 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#286 -t1 -s1 "D03 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#287 -t1 -s1 "D04 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#288 -t1 -s1 "D05 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#289 -t1 -s1 "D06 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#290 -t1 -s1 "D07 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#291 -t1 -s1 "D08 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#292 -t1 -s1 "D09 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#293 -t1 -s1 "D10 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#294 -t1 -s1 "D11 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#295 -t1 -s1 "D12 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#296 -t1 -s1 "D13 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#297 -t1 -s1 "D14 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#298 -t1 -s1 "D15 tool offset" -s2 "mm" -m15 -min=-999.999 -max=999.999
#299 -M0
#374 -t2 -s1 "Enable software limit" -s3 "0:not enable,1:enable" -m11 -min=0.000 -max=1.000 -i0 "Disable" -i1 "Enable "
#375 -t1 -s1 "Soft-limited postion value of X--" -s2 "mm" -m11 -min=-9999.000 -max=9999.000
#376 -t1 -s1 "Soft-limited postion value of Y--" -s2 "mm" -m11 -min=-9999.000 -max=9999.000
#377 -t1 -s1 "Soft-limited postion value of Z--" -s2 "mm" -m11 -min=-9999.000 -max=9999.000
#378 -t1 -s1 "Soft-limited postion value of A--" -s2 "deg" -m11 -min=-9999.000 -max=9999.000
#379 -t1 -s1 "Soft-limited postion value of X++" -s2 "mm" -m11 -min=-9999.000 -max=9999.000
#380 -t1 -s1 "Soft-limited postion value of Y++" -s2 "mm" -m11 -min=-9999.000 -max=9999.000
#381 -t1 -s1 "Soft-limited postion value of Z++" -s2 "mm" -m11 -min=-9999.000 -max=9999.000
#382 -t1 -s1 "Soft-limited postion value of A++" -s2 "deg" -m11 -min=-9999.000 -max=9999.000
#390 -t2 -s1 "X axis DIR signal Electric Level" -m2 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#391 -t2 -s1 "Y axis DIR signal Electric Level" -m2 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#392 -t2 -s1 "Z axis DIR signal Electric Level" -m2 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#393 -t2 -s1 "A axis DIR signal Electric Level" -m2 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#395 -t2 -s1 "support of G53 coordinate sys" -s3 "0:support,1:not support" -m0 -min=0.000 -max=1.000 -i0 "Yes" -i1 "No "
#396 -t0 -s1 "Number of line" -m16 -min=100.000 -max=3600.000
#400 -t2 -s1 "Limited siganl active of X--" -s3 "0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0 "Disable" -i1 "Enable "
#401 -t2 -s1 "Limited siganl active of Y--" -s3 "0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0 "Disable" -i1 "Enable "
#402 -t2 -s1 "Limited siganl active of Z--" -s3 "0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0 "Disable" -i1 "Enable "
#403 -t2 -s1 "Limited siganl active of A--" -s3 "0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0 "Disable" -i1 "Enable "
#404 -t2 -s1 "Limited siganl active of X++" -s3 "0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0 "Disable" -i1 "Enable "
#405 -t2 -s1 "Limited siganl active of Y++" -s3 "0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0 "Disable" -i1 "Enable "
#406 -t2 -s1 "Limited siganl active of Z++" -s3 "0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0 "Disable" -i1 "Enable "
#407 -t2 -s1 "Limited siganl active of A++" -s3 "0:not enable,1:enable" -m10 -min=0.000 -max=1.000 -i0 "Disable" -i1 "Enable "
#408 -t2 -s1 "Effective electric level of X--" -m10 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#409 -t2 -s1 "Effective electric level of Y--" -m10 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#410 -t2 -s1 "Effective electric level of Z--" -m10 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#411 -t2 -s1 "Effective electric level of A--" -m10 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#412 -t2 -s1 "Effective electric level of X++" -m10 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#413 -t2 -s1 "Effective electric level of Y++" -m10 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#414 -t2 -s1 "Effective electric level of Z++" -m10 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#415 -t2 -s1 "Effective electric level of A++" -m10 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#416 -t0 -s1 "Time interval between DIR & pulse" -s2 "ns" -m2 -min=0.000 -max=9999.000
#418 -t2 -s1 "X axis Pulse signal Electric Level" -m2 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#419 -t2 -s1 "Y axis Pulse signal Electric Level" -m2 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#420 -t2 -s1 "Z axis Pulse signal Electric Level" -m2 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#421 -t2 -s1 "A axis Pulse signal Electric Level" -m2 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#422 -t2 -s1 "definition of PWM Electric level" -m6 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#423 -t2 -s1 "Enable signal of extended ESTOP" -s3 "0:not enable,1:enable" -m13 -min=0.000 -max=1.000 -i0 "Disable" -i1 "Enable "
#424 -t2 -s1 "Electric level of ext-ESTOP signal" -m13 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#425 -t2 -s1 "Enable extended START&PAUSE" -s3 "0:not enable,1:enable" -m13 -min=0.000 -max=1.000 -i0 "Disable" -i1 "Enable "
#426 -t2 -s1 "Electric level of extended START" -m0 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#427 -t2 -s1 "Electric level of extended PAUSE" -m0 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#428 -t2 -s1 "Enable the ESTOP signal on MPG" -s3 "0:not enable,1:enable" -m12 -min=0.000 -max=1.000 -i0 "Disable" -i1 "Enable "
#429 -t2 -s1 "Electric level of ESTOP on MPG" -m12 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#430 -t2 -s1 "MPG interface type" -s3 "0-serial port MPG£¬1-standard MPG" -m12 -min=0.000 -max=1.000 -i0 "Serial" -i1 "Standard "
#431 -t1 -s1 "MPG Precision " -m12 -min=0.001 -max=0.01
#432 -t2 -s1 "Standard MPG signal Electric Level" -m12 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#433 -t0 -s1 "PWM rising rate from 0V to 10V" -m6 -min=0.000 -max=65535.000
#434 -t2 -s1 "A/B phase signal level on MPG" -m12 -min=0.000 -max=1.000 -i0 "Low" -i1 "High "
#435 -t1 -s1 "X axis protection speed" -s2 "mm/min" -m4 -min=99.000 -max=99999.000
#436 -t1 -s1 "Y axis protection speed" -s2 "mm/min" -m4 -min=99.000 -max=99999.000
#437 -t2 -s1 "enable of X axis backlash" -s3 "0:not enable,1:enable" -m14 -min=0.000 -max=1.000 -i0 "Disable" -i1 "Enable "
#438 -t2 -s1 "enable of Y axis backlash" -s3 "0:not enable,1:enable" -m14 -min=0.000 -max=1.000 -i0 "Disable" -i1 "Enable "
#439 -t2 -s1 "enable of Z axis backlash" -s3 "0:not enable,1:enable" -m14 -min=0.000 -max=1.000 -i0 "Disable" -i1 "Enable "
#440 -t2 -s1 "enable of A axis backlash" -s3 "0:not enable,1:enable" -m14 -min=0.000 -max=1.000 -i0 "Disable" -i1 "Enable "
#441 -t1 -s1 "X axis backlash distance" -s2 "mm" -m14 -min=0.000 -max=0.999
#442 -t1 -s1 "Y axis backlash distance" -s2 "mm" -m14 -min=0.000 -max=0.999
#443 -t1 -s1 "Z axis backlash distance" -s2 "mm" -m14 -min=0.000 -max=0.999
#444 -t1 -s1 "A axis backlash distance" -s2 "deg" -m14 -min=0.000 -max=9.999
#445 -t1 -s1 "Backlash Speed" -s2 "mm/min" -m14 -min=99.000 -max=99999.000
#446 -t2 -s1 "Define the extended key function" -m13 -min=0.000 -max=1.000 -i0 "START" -i1 "Find Middle "
#447 -t2 -s1 "Define the Function of Ext-key2" -m13 -min=0.000 -max=1.000 -i0 "PAUSE" -i1 "ZERO "
#449 -s1 "ZERO "
#450 -s1 "GOTOZ "
#451 -s1 "HOME "
#452 -s1 "PROBE "
#453 -s1 "AUTO "
#454 -s1 "SIMULATE "
#455 -s1 "CONT "
#456 -s1 "STEP "
#457 -s1 "MPG "
#458 -s1 "RESET "
#459 -s1 "READY "
#460 -s1 "BUSY "
#461 -s1 "FRO: "
#462 -s1 "SRO: "
#463 -s1 "SJR "
#464 -s1 "Start Line: "
#465 -s1 "2ND "
#466 -s1 "syntax check "
#467 -s1 "Main Page "
#468 -s1 "File Page "
#469 -s1 "Param Page "
#470 -s1 "Normal Mod "
#471 -s1 "X-:gotoz Y-:zero Z-:home "
#472 -s1 "A-:probe Start:goto break "
#473 -s1 "X-:all gotoz X+:x gotoz "
#474 -s1 "Y+:y gotoz Z+:z gotoz "
#475 -s1 "A-:go probe "
#476 -s1 "X+:left X-:right Y+:up Y-:down "
#477 -s1 "Z-:enter Z+:cancel "
#478 -s1 "Y-:all zero X+:x zero "
#479 -s1 "Y+:y zero Z+:z zero "
#480 -s1 "Z-:all home X+:x home "
#481 -s1 "Y+:y home Z+:z home "
#482 -s1 "soft limit: "
#483 -s1 "TRCUT "
#484 -s1 "EDIT "
#485 -s1 "SBK "
#495 -t1 -s1 "interpolation period" -s2 "s" -m16 -min=0.002 -max=0.010
#497 -t1=0.000
#498 -t0=4.000
#499 -t1=888888.000 -s1 "user access key" -m16 -min=0.000 -max=999999.000
Last update: 2021-10-22
Created: 2021-10-22
Created: 2021-10-22